Electrical FAQ

We dispatch 24/7 across Illinois and the surrounding area. Most urgent calls are reached the same day, often within hours, depending on your location and current call volume.

Loss of power that the utility has not caused, sparking or smoking outlets, a burning smell, exposed live wires, a hot breaker panel, water contact with electrical equipment, or any shock. If you are unsure, call us – it costs nothing to ask.

Flickering usually points to a loose neutral, an overloaded circuit, a failing breaker, or a utility supply issue. We test each possibility and repair the fault.

Yes. A dead outlet is often a tripped GFCI, a loose wire, or a burned contact. We repair or replace it and confirm the circuit is safe.

Most 200 amp panel upgrades fall in a mid four-figure range depending on the service entrance, grounding, and utility requirements. We provide a written quote after a free on-site assessment.

Warning signs include frequent tripping, warm breakers, a fuse box, a recalled panel brand, buzzing, or not enough space to add circuits.

Cost depends on square footage, number of stories, access, and finish repair. We give a fixed written quote after walking the home.

Usually not. We work room by room and restore power each evening for most projects.

Most homes run essentials on 14–22 kW; whole-home coverage with central air typically needs 22–26 kW. We perform a load calculation before recommending a unit.

Once the unit and pad are on site, electrical installation and transfer switch work are usually completed in 1–2 days.

A typical Level 2 install near the panel is in the high hundreds to low thousands; longer runs or panel upgrades add cost. We quote in writing before work begins.

We check your available capacity. If the panel is full, options include a load-management device or a 200 amp upgrade.

Adding an outlet on an existing circuit is one of our most affordable services; a new dedicated circuit costs more. Call (888) 592-6466 for a quick quote.

Kitchens, bathrooms, laundry, garages, basements, outdoors and within 6 feet of a sink.

A common rule is one 4–6 inch LED can per 4–6 feet of ceiling. We lay out the spacing for even light before cutting.

Yes. We install fan- or fixture-rated boxes and bracing for heavy fixtures and high ceilings.

Yes. We run a new circuit or extend an existing one, install a fan-rated box, and add a wall switch.

A straightforward replacement is about an hour; new wiring or high ceilings take longer.

Modern LED landscape lighting uses a fraction of the power of halogen and lasts for years.

Yes, we install motion-sensor floods on existing or new circuits.

Older dimmers are not rated for LED bulbs. We install LED-compatible dimmers that solve the problem.

Often yes – we use no-neutral smart switches or run a neutral where needed.

Refrigerators, ranges, dishwashers, microwaves, dryers, hot tubs, HVAC, EV chargers and anything over 1,500 watts.

Yes – we install the GFCI disconnect, conduit and bonding required for spas.

Common causes are overload, a short circuit, a ground fault or a worn breaker. We test to find the real cause.

Working inside a live panel is dangerous. Breaker replacement should be done by an electrician.

Yes – Illinois storms and grid switching cause surges that quietly shorten the life of electronics and HVAC boards. A single device at the panel protects everything downstream.

It diverts most surge energy safely to ground. No device guarantees protection from a direct strike, but layered protection dramatically reduces damage.

Our inspections are affordably priced and often credited toward any repairs you choose to make. Call (888) 592-6466 for current pricing.

Panel condition, breaker sizing, grounding, GFCI/AFCI protection, outlet and switch condition, visible wiring, smoke detectors and more.

Yes – from a single smart switch to full-home lighting and network wiring.

Yes. We install or upgrade the transformer, wiring and chime so your doorbell camera stays powered.

Yes – we provide maintenance agreements, fast response and clear documentation for property managers and facility teams.

Yes. We install and repair 208V and 480V three-phase systems.

Yes – nights and weekends are available for occupied offices.

Yes. We run and terminate Cat6/Cat6A and coax alongside power.

Most commercial retrofits cut lighting costs 50–70% and pay back in 1–3 years, especially with utility rebates.

Often yes – we use ballast-bypass tubes or retrofit kits where appropriate.

We perform the electrical hookup, panel and battery work for solar systems and partner with installers for roof mounting.

Most batteries power essential loads for many hours; multiple units or a generator hybrid can cover more.